The cycle has ended, but the clothes are sitting in a pool of gray water and the door will not open.
A washer not draining is a common washing machine problem. Water stays in the drum after the wash or rinse, the clothes come out soaking wet, or the machine stops mid-cycle with an error code.
In this guide, we’ll explain why a washing machine won’t drain, what you can safely check yourself, how front-load and top-load washers differ, and when the problem needs a technician.
Why Is My Washer Not Draining?
To drain, the washer pumps water out of the drum, through a filter and a hose, and into the house drain. A problem at any point along that path leaves water in the drum.
Water Stays in the Drum, Pump Is Humming
The pump is trying to run, but something is in the way. A clogged pump filter, a sock in the pump, or a blocked drain hose is the usual cause.
Water Stays in the Drum, No Pump Sound
If the washer is silent when it should be draining, the drain pump, the lid switch or door lock, or the control may have failed.
Water Backs Up Out of the Drain Pipe
If water backs up out of the standpipe or the laundry sink while the washer drains, the household drain may be clogged or unable to handle the flow. A plumber should inspect the drain system.
Washer Drains Slowly or Leaves Clothes Soaked
A kinked drain hose, a partly clogged filter, or too many suds slows the drain so the washer cannot finish the spin.
What to Check First When a Washer Won’t Drain
Work through these checks in order. The first four need no tools and do not involve opening anything on the washer.
Run a Drain and Spin Cycle
Cancel the current cycle and select Drain and Spin or Rinse and Spin. A power interruption or a paused cycle can leave water in the drum without any fault.
Check the Drain Hose Behind the Washer
Make sure the drain hose is not kinked, crushed against the wall, or inserted too far into the standpipe. It should sit at the height and depth given in the washer’s installation instructions. Incorrect hose placement can cause drain or siphoning problems.
Check the House Drain
Look at the standpipe or laundry sink the hose drains into. Standing water or slow draining there points to a clog in the household drain.
Look for Too Many Suds
Too much detergent, or the wrong type, creates excess suds. The foam can keep the drain pump from removing water and trigger a drain error. Use HE detergent in an HE washer and follow the recommended amount for the load.
Clean the Drain Pump Filter on a Front-Load Washer
Many front-load washers have a small access door at the bottom front, but filter access varies by model. If your washer has a drain pump filter you can reach, unplug the machine and let any hot water cool. Place towels and a shallow pan underneath. Use the emergency drain hose if there is one, then loosen the filter slowly to release the remaining water. Remove lint, coins, and other debris, and screw the filter back in firmly.
After these checks, run Drain and Spin again. If the water still does not leave the drum, the washer needs diagnosis.
Expect water to come out, and remember that it may be hot after a warm or sanitize cycle. Do not reach into the pump with the washer plugged in, and do not force the door open while water is still in the drum.
7 Reasons a Washing Machine Won’t Drain
If the basic checks did not solve it, one of these causes is likely.
1. Clogged Drain Pump Filter
The filter catches coins, hair ties, lint, and small items of clothing before they reach the pump. When it fills up, water cannot pass through.
2. Kinked or Clogged Drain Hose
A hose bent behind the washer or packed with lint restricts the flow. A small sock can also lodge in the hose between the drum and the pump.
3. Failed Drain Pump
The pump motor can burn out, or the impeller inside can break or jam. A failed pump may hum without moving water or make no sound at all. On some older washer designs, a worn or broken drive belt can also keep the pump from operating.
4. Clogged Standpipe or House Drain
Lint and soap residue build up in the drain pipe over time. The washer pumps normally, but the water has nowhere to go and may overflow.
5. Faulty Lid Switch or Door Lock
A faulty lid switch or door lock can keep the washer from starting or finishing its drain and spin sequence. The exact symptoms depend on the washer’s design and safety controls.
6. Too Much Detergent or Suds
Regular detergent in an HE washer, or too much of any detergent, makes more foam than the pump can clear. The washer may pause and add rinses or stop with an error.
7. Control or Water Level Sensor Fault
A faulty control board, pressure sensor, or pressure hose can keep the washer from reading the water level and running the drain cycle correctly.
Front-Load Washer vs. Top-Load Washer Not Draining
Both types use a drain pump, but they differ in how you reach the filter and which parts stop the cycle.
Front-Load Washer Not Draining
Front-load washers usually have a pump filter you can reach from the front, and the door stays locked while water is in the drum.
Possible faults:
- Clogged pump filter
- Item lodged in the pump or hose
- Failed drain pump
- Door lock fault
- Kinked drain hose
Top-Load Washer Not Draining
Most top-load washers have no filter the owner can reach. The pump sits under the tub and is reached from the back or the bottom.
Possible faults:
- Failed lid switch or lid lock
- Item lodged in the pump
- Failed drain pump
- Kinked or clogged drain hose
- Worn belt on older models
On a front-load washer, a door that stays locked with water inside is normal. Once the water is drained, the lock should release. If it does not, see our guide to a washer door that won’t unlock.
Washer Not Draining: Symptoms and Likely Causes
Use this table to connect what you are seeing with the most likely cause and the next step.
| Symptom | Possible Cause | Recommended Action |
|---|---|---|
| Water in the drum, pump humming | Clogged filter, item in the pump, or blocked hose | Clean the pump filter if your model has one. If water remains, schedule a repair. |
| Water in the drum, no pump sound | Failed pump, lid switch or door lock, or control fault | Run Drain and Spin once. If the pump stays silent, schedule a repair. |
| Drains slowly, clothes very wet | Partly clogged filter, kinked hose, or too many suds | Check the hose, clean the filter, and reduce detergent. |
| Water backs up from the drain pipe | Clogged standpipe or house drain | Stop the washer and have a plumber inspect the drain. |
| Drains but does not spin | Unbalanced load, lid lock, or drive problem | Redistribute the load and run Spin again. |
| Grinding or rattling during drain | Coin or debris in the pump, or damaged impeller | Stop the cycle and schedule a repair. |
| Error code on the display | Brand-specific drain fault | Write down the code and share it when you book service. |
If the washer drains but the clothes stay wet, the spin is the problem. Our guide to a washing machine that won’t spin covers that case.
Washer Drain Error Codes by Brand
Many washers show an error code when the drain takes longer than expected or the machine cannot remove the water. Codes vary by brand, model, and control system, so always check the owner’s manual before diagnosing the problem.
| Brand | Common Drain Code | What It Means |
|---|---|---|
| LG | OE | The washer did not drain within the expected time. |
| Samsung | 5E, 5C, or SE | Drain problem. Water did not leave the drum in time. |
| Whirlpool and Maytag | F9 E1 | Long drain. The drain step took longer than allowed. |
| Bosch | E18 | Drain fault, often a clogged pump filter or hose. |
Our LG error code guide explains the OE code in more detail. For brand-specific service, see our pages for LG, Samsung, Whirlpool, and Bosch appliance repair.
When Does a Washer That Won’t Drain Need Professional Repair?
If the hose is clear, the house drain works, and the filter is clean, the fault is inside the washer. Reaching the pump means removing panels and disconnecting hoses that hold water.
Schedule Service If You Notice Any of These
- Water stays in the drum after you clean the filter and check the hose.
- The pump hums or grinds but does not move water.
- The pump makes no sound during the drain step.
- The same drain error code keeps coming back.
- Water is leaking from under the washer.
Do not keep restarting the cycle with water in the drum. Each attempt can add more water, and a jammed pump can overheat.
If the washer also has trouble at the start of the cycle, our guide to a washer not filling with water covers the fill side of the system.
A technician can test the pump, the lid switch or door lock, and the control, remove anything lodged in the pump, and confirm the cause before replacing parts. Our professional washer repair service covers front-load and top-load models.
Is It Worth Repairing a Washer That Won’t Drain?
In most cases, yes. A clog costs little to clear, and a drain pump is one of the more affordable washer parts to replace.
Repair Usually Makes Sense When
- The washer is otherwise in good condition.
- The cause is a clog, the pump, the lid switch, or the door lock.
- The drum spins quietly and the washer does not leak.
- It is a higher-end or matched laundry set you want to keep.
Replacement May Make More Sense When
- The drum bearings are loud or the tub is damaged.
- The control board and other parts have failed together.
- The washer has needed several repairs in a short time.
- Parts for the model are no longer available.
For a wider look at this decision, see our guide on whether to repair or replace an appliance.
Washer Not Draining: Frequently Asked Questions
Why is there water left in my washing machine after the cycle?
The water could not get out in time. The usual causes are a clogged pump filter, a kinked or blocked drain hose, a failed drain pump, or a clogged house drain.
How do I drain a washing machine that won’t drain?
Unplug the washer first. If your washer has an emergency drain hose, use it as the owner’s manual describes. Otherwise, check the manufacturer’s instructions for your model before you try to remove standing water. Keep towels and a shallow container ready, and do not force the door open while water remains in the drum.
Where is the drain pump filter on my washer?
On most front-load washers it is behind a small door at the bottom front corner. Many top-load washers do not have a filter the owner can reach. Check the owner’s manual for your model.
Why is my washer humming but not draining?
The pump motor is powered but cannot move water. Something is blocking the filter or the impeller, or the impeller is broken. Stop the cycle so the pump does not overheat.
Can a clogged house drain stop my washer from draining?
Yes. If water comes back up the standpipe or into the laundry sink, the household drain is likely blocked. A plumber should inspect it.
Can too much detergent keep a washer from draining?
Yes. Excess suds can keep the pump from removing water and trigger a drain error. Use HE detergent in an HE washer and follow the amount on the label.
Why won’t my washer door open when it is full of water?
Front-load washers keep the door locked while water is in the drum so it cannot spill out. Drain the water first. The lock normally releases a few minutes later.
Is it safe to keep using a washer that drains slowly?
It is better to fix it first. A slow drain puts extra load on the pump, leaves clothes wet, and can end in a washer full of water that will not empty at all.
Washer Still Not Draining? We Can Help.
If your washing machine won’t drain and the basic checks have not solved it, North Appliance Service can find the cause and repair it.
We diagnose drain pumps, clogged filters and hoses, lid switches, door locks, and control faults on front-load and top-load washers from most major brands.
Serving Seattle, Bellevue, Kirkland, Redmond, Bothell, Sammamish, Lynnwood, Everett, and nearby communities in King and Snohomish Counties.
Safety note: Drain systems, filter locations, and error codes vary by manufacturer and model. Always follow the owner’s manual. Unplug the washer before opening the pump filter, and never force a locked door or work on internal electrical parts without proper training.





