Your dryer tumbles, the timer counts down, and the clothes come out as wet as they went in.
A dryer not heating is one of the most common dryer problems we see. The drum turns and the controls respond, but the air inside stays cold, so a normal load can run for hours without drying.
In this guide, we’ll explain why a dryer runs but produces no heat, what you can safely check yourself, how the causes differ between electric and gas dryers, and when it is time to call a technician.
Why Is My Dryer Not Heating?
The way the problem shows up is a useful clue. Match what you see to the closest description below before you check anything else.
Dryer Runs Cold on One Cycle Only
Air Fluff, Air Dry, and some Eco or Delicate cycles use little or no heat by design. Try Timed Dry on high heat before assuming a fault.
Electric Dryer Tumbles but Never Warms Up
An electric dryer needs both halves of its 240-volt circuit to heat. With one half tripped, the drum can still turn while the heater gets no power.
Dryer Heats at First, Then Goes Cold
A clogged vent traps heat inside the dryer. Safety parts then cut the heater off, and loads need two or more cycles to dry.
No Heat at All After the Basic Checks
A burned-out heating element, a blown thermal fuse, a failed igniter, or weak gas valve coils will stop the heat completely until the part is replaced.
What to Check First When a Dryer Is Not Heating
These checks need no tools and do not involve opening the dryer. Work through them in order, then run a short test load.
Confirm the Cycle and Temperature Setting
Select Timed Dry and the highest heat setting that suits the load. Make sure Air Fluff or Air Dry is not selected. If your dryer has Eco or Delicate settings, try a regular heated cycle instead.
Reset the Breaker on an Electric Dryer
Find the double breaker labeled for the dryer. Switch it fully off, then back on. A breaker can be half-tripped without looking different from the others.
Check the Gas Supply on a Gas Dryer
The shutoff valve behind the dryer should have its handle in line with the pipe. If other gas appliances in the home are also not working, contact your gas utility.
Clean the Lint Screen and Look Behind the Dryer
Remove the lint from the screen, then check that the vent hose behind the dryer is not crushed, kinked, or disconnected.
Check the Vent Outlet Outside
With the dryer running, the flap on the outside vent hood should open and you should feel a strong flow of air. Weak airflow points to a blocked vent.
After these checks, run a few damp towels on Timed Dry at high heat for ten minutes. If the towels and the air inside the drum are still cold, the dryer needs diagnosis.
If you smell gas, do not operate the dryer or any switches. Leave the home and call your gas utility from outside. If you notice a burning smell, turn the dryer off and unplug it. Our guide to a dryer that smells like burning explains what that smell can mean.
7 Reasons a Dryer Stops Heating
If the basic checks did not bring the heat back, one of these faults is the likely cause. Some apply only to electric dryers, some only to gas dryers, and some to both.
1. Tripped Breaker or Power Supply Fault
The motor runs on half of the circuit, the heater needs all of it. A tripped breaker, a damaged power cord, or a burned terminal block leaves the dryer running without heat.
2. Blown Thermal Fuse
The thermal fuse is a one-time safety part that opens when the dryer overheats. It does not reset. On most dryers a blown fuse cuts the heat, and on some models it stops the dryer from running at all.
3. Burned-Out Heating Element
The heating element is a coil of wire that glows hot when powered. Over time the coil can break or short against its housing, and the dryer stops producing heat.
4. Failed Igniter
The igniter glows to light the gas at the burner. When it cracks or weakens it cannot light the flame, so the drum turns but the burner never fires.
5. Weak Gas Valve Coils
The coils open the gas valve. As they wear out, they often work when cold and fail once warm. The dryer heats for the first few minutes and then runs cold for the rest of the cycle.
6. Faulty Thermostat or Temperature Sensor
A faulty cycling thermostat, high-limit thermostat, or thermistor can cause incorrect temperature control or keep the heating system from operating. The exact effect depends on the dryer model and its control system.
7. Clogged Vent or Lint Buildup
A restricted vent can make the dryer overheat and trip safety parts such as the high-limit thermostat or the thermal fuse. If the airflow is not corrected, the same overheating can damage the replacement parts.
Less often, the cause is a failed timer, a control board fault, or a worn switch inside the drive motor. These need electrical testing to confirm. If lint buildup is part of the problem, read why dryer vent cleaning matters beyond the lint screen.
Electric Dryer vs. Gas Dryer: Why the Cause Differs
Both types tumble clothes the same way, but they make heat differently. Knowing which type you have narrows the list of possible faults.
Electric Dryer Not Heating
An electric dryer plugs into a large 240-volt outlet and heats with an electric element.
Possible faults:
- Half-tripped double breaker
- Burned-out heating element
- Blown thermal fuse
- Failed high-limit or cycling thermostat
- Damaged power cord or terminal block
Gas Dryer Not Heating
A gas dryer uses a standard 120-volt outlet and a gas line, and heats with a burner.
Possible faults:
- Closed gas shutoff valve
- Failed igniter
- Weak gas valve coils
- Faulty flame sensor
- Blown thermal fuse
Not sure which type you have? Look behind the dryer. A flexible gas line and a regular three-prong plug mean a gas dryer. A thick cord with a large three- or four-prong plug means an electric dryer.
Dryer Not Heating: Symptoms and Likely Causes
Use this table to connect what you are seeing with the most likely cause and the next step.
| Symptom | Possible Cause | Recommended Action |
|---|---|---|
| Electric dryer runs but no heat at all | Half-tripped breaker, heating element, or thermal fuse | Reset the breaker once. If there is still no heat, schedule a repair. |
| Gas dryer igniter glows but no flame | Weak gas valve coils or closed gas supply | Confirm the shutoff valve is open, then schedule a repair. |
| Heats for a few minutes, then goes cold | Gas valve coils, cycling thermostat, or restricted vent | Check the vent for blockage. If airflow is good, schedule a repair. |
| Clothes need two or more cycles | Clogged vent or heavy lint buildup | Clean the lint screen and have the vent inspected. |
| Dryer feels very hot or shuts off mid-cycle | Restricted airflow or another fault triggering a safety device | Stop using the dryer and have the airflow and heating system inspected. |
| Sensor cycle ends early with damp clothes | Dirty moisture sensor bars or a mixed load | Clean the sensor bars as the owner’s manual describes and try Timed Dry. |
| Error code on the display | Brand-specific heating or airflow fault | Write down the code and share it when you book service. |
When Does a Dryer That Won’t Heat Need Professional Repair?
If the settings, breaker, gas valve, lint screen, and vent all check out and the dryer still runs cold, the fault is inside the machine. Finding it means testing parts with a meter.
Schedule Service If You Notice Any of These
- No heat after resetting the breaker and running a timed high-heat cycle.
- The breaker trips again after you reset it.
- The dryer heats briefly and then runs cold on every load.
- The top or sides of the dryer feel unusually hot.
- You notice a burning smell, scorch marks, or a gas smell.
Do not bypass a blown thermal fuse to get the heat back. The fuse opened because the dryer overheated, and running without it removes the protection against a fire.
Do not keep resetting a breaker that trips again, and do not run the dryer with the vent hose disconnected. On a gas dryer, a disconnected vent releases exhaust gases, including carbon monoxide, into the home.
A technician can test the heating circuit, confirm which part failed, and check the airflow so the new part is not damaged by the same problem. Our professional dryer repair service covers both electric and gas models.
Is It Worth Repairing a Dryer That Won’t Heat?
In most cases, yes. Dryers are mechanically simple, and the parts that stop the heat are usually replaceable without rebuilding the machine.
The right choice depends on the age of the dryer, its overall condition, and whether this is the first problem or one of several.
Repair Usually Makes Sense When
- The dryer is otherwise in good condition.
- The fault is a single part such as a fuse, element, igniter, or thermostat.
- The drum, motor, and controls work normally.
- It is a higher-end or matched laundry set you want to keep.
Replacement May Make More Sense When
- The dryer has needed several repairs in a short time.
- The drum, bearings, or motor are also worn.
- Parts for the model are no longer available.
- The cabinet or drum shows rust or heat damage.
For a wider look at this decision, see our guide on whether to repair or replace an appliance.
Dryer Not Heating: Frequently Asked Questions
Why is my dryer running but not heating?
The motor and the heater are separate circuits. The drum can turn normally while a tripped breaker, a blown thermal fuse, a failed heating element, or a gas ignition fault keeps the heat off.
Can a clogged vent cause a dryer not to heat?
Yes. A blocked vent traps hot air inside the dryer. The safety thermostat or thermal fuse then cuts power to the heater. Until the vent is cleared, the problem tends to come back.
How do I know if the thermal fuse is blown?
There is no visible sign from outside. A technician checks the fuse for continuity with a meter. A blown fuse usually means the dryer overheated, so the vent should be inspected at the same visit.
Why does my gas dryer igniter glow but not light?
If the igniter glows but the burner does not light, the problem may be weak gas valve coils, a gas supply issue, or another part of the ignition system. Testing is needed to identify the cause, and it should be left to a technician.
Why does my dryer heat up and then stop heating?
On a gas dryer, worn valve coils often fail once they warm up. On any dryer, restricted airflow can trip the high-limit thermostat, which switches the heater off partway through the cycle.
Is it safe to keep using a dryer that is not heating?
It is better to stop. Running cycle after cycle wastes energy and can hide an overheating or airflow problem. If you notice a burning or gas smell, stop using the dryer right away.
Can I replace a dryer heating element myself?
It involves opening the cabinet and working on a 240-volt circuit, so we do not recommend it without training. The element should also be tested first, because several other parts cause the same symptom.
Why are my clothes still damp when the dryer feels warm?
Warm air with poor airflow cannot carry moisture out of the drum. Check the lint screen and vent first. On sensor cycles, dirty moisture sensor bars can also end the cycle too early.
Dryer Still Not Heating? We Can Help.
If your dryer runs but will not heat and the basic checks have not solved it, North Appliance Service can find the cause and repair it.
We diagnose heating elements, thermal fuses, thermostats, igniters, gas valve coils, and airflow problems on electric and gas dryers from most major brands.
Serving Seattle, Bellevue, Kirkland, Redmond, Bothell, Sammamish, Lynnwood, Everett, and nearby communities in King and Snohomish Counties.
Safety note: Dryer heating systems, safety devices, and reset procedures vary by manufacturer and model. Always follow the owner’s manual. Never bypass a thermal fuse or thermostat, and never work on gas connections or internal electrical parts without proper training.






